Include physical subwoofer displacement by adding the installed driver’s occupied volume to the desired net air-volume target. Add braces, internal ducts, and other excluded space separately, and confirm whether a manufacturer plan has already included those allowances.
Open the Driver Displacement Calculator.
How to Include Subwoofer Displacement in a Box Design
The key design relationship is:
Required gross internal volume = net target + total driver physical displacement + other internal displacement
Gross internal volume is the cavity enclosed by the panels before accounting for objects inside it. Net volume is the air cavity remaining under the chosen enclosure-design convention. Exterior volume also includes wall thickness and is a separate quantity.
The calculator takes a net target in liters, a documented physical displacement per identical installed driver, driver count, and a combined allowance for other internal displacement. It can report either the required gross internal volume or the total physical displacement of the drivers.
It does not infer driver displacement from nominal cone diameter or Xmax. Those inputs describe different physical quantities and cannot reliably determine the space occupied by the installed motor and basket.
Use the arithmetic after establishing an appropriate acoustic target. A correct displacement allowance does not prove that the target volume suits the chosen driver, power, filtering, or enclosure alignment.
Separate Three Meanings of Displacement
Physical driver displacement is the volume excluded from the enclosure’s air cavity by the installed driver structure. This is the quantity needed when converting a net box target into gross internal space.
Cone swept volume is commonly calculated as effective piston area multiplied by one-way excursion: Vd = Sd × Xmax, under the stated convention. It describes an excursion-related capability rather than the basket’s occupied space.
An enclosure’s total geometric volume is different again. It may be measured outside the panels, inside the panels, or after deductions. A number labeled only “displacement” or “volume” needs its boundary clarified before use.
For a hypothetical driver with Sd of 530 cm² and one-way Xmax of 12 mm, swept volume is 530 × 1.2 = 636 cm³, or 0.636 L. That calculation provides no basis for claiming the same driver’s physical enclosure displacement is 0.636 L.
A manufacturer could document a different physical displacement, such as the illustrative 2.1 L used below. The two values can coexist because they answer different questions. Neither should replace the other in a worksheet merely because both have volume units.
Start With the Manufacturer’s Volume Convention
Read the actual driver manual and recommended enclosure plan. Identify whether its stated volume is net air space, gross internal space, or a complete dimensional construction that already includes the installed driver.
JL Audio’s enclosure-volume guidance through Garmin support addresses the distinction between internal volume and displacement. Its practical implication is that the starting number and deductions must use the same convention.
For a net-volume target, add physical displacement to determine the required gross cavity. For an existing gross cavity, subtract displacement to determine the remaining net volume. These are inverse operations, not two allowances to apply consecutively.
If a published cut plan already produces the specified net volume with the stated driver and braces installed, follow that plan’s instructions. Increasing its dimensions to add the same driver displacement again changes the intended alignment.
Record any uncertainty in the source wording. A note such as “net target before driver and brace allowance” avoids later confusion when someone uses the worksheet to change the enclosure shape or driver quantity.
Work Through a Two-Subwoofer Design
Assume the intended shared chamber requires a hypothetical 42 L net air-volume target. Each of two identical drivers has a documented physical displacement of 2.1 L in the intended mounting arrangement.
The combined driver allowance is:
Vdrivers = 2 × 2.1 = 4.2 L
Assume braces, terminal hardware, and any other excluded internal objects total another 1.3 L. Required gross internal volume is:
Vgross = 42 + 4.2 + 1.3 = 47.5 L
Select gross internal volume in the calculator to obtain 47.5 L. Select total driver displacement to obtain 4.2 L. The latter is one component of the budget, not the complete cavity size.
| Design item | Volume |
|---|---|
| Intended net air cavity | 42.0 L |
| First installed driver | 2.1 L |
| Second installed driver | 2.1 L |
| Other internal displacement | 1.3 L |
| Required gross internal cavity | 47.5 L |
The example assumes a shared chamber. If each driver needs an independent sealed chamber, calculate each chamber separately, including its own physical displacement and brace arrangement. A partition changes both geometry and the volume allocation.
Convert the Gross Target Into Internal Dimensions
For a rectangular cavity measured in centimeters:
Vliters = internal width × internal height × internal depth / 1000
An illustrative internal shape of 50 by 38 by 25 cm gives 50 × 38 × 25 / 1000 = 47.5 L. After the 5.5 L combined displacement allowance, it leaves the 42 L target.
These dimensions are one geometric solution, not an optimized enclosure shape. The actual driver depth, mounting cutouts, brace openings, basket clearance, and assembly method must fit the selected arrangement.
With a simple uniform 18 mm wall on all sides, the corresponding outer axes would each increase by 3.6 cm, giving 53.6 by 41.6 by 28.6 cm. A double baffle, inset panel, or different panel-overlap construction changes that conversion.
Derive the cut list from a section drawing of the actual joints. Do not assume that every panel shares the full outside dimensions or that subtracting twice one nominal thickness describes every cavity detail.
After choosing a physical shape, recalculate the brace volume. A longer or differently shaped cabinet can require a different brace arrangement, which changes the displacement budget that produced the original dimensions.
Account for Ports, Braces, and Internal Compartments
For a vented enclosure, keep the net cavity air volume distinct from the air inside the port duct. The model’s definition of box volume and port geometry determines how that space is treated.
Include the internal portion of a duct and its wall material in the excluded space according to the selected plan convention. An external port section does not displace internal cavity space merely because it is part of the same physical duct.
For a slot port sharing enclosure walls, calculate the actual internal geometry rather than adding a complete freestanding rectangular tube that does not exist. Avoid double counting shared wall material or brace intersections.
Solid braces can be calculated from their dimensions. Window braces require subtracting the openings from the material envelope. Other components may need a documented geometry estimate if the manufacturer does not provide their occupied volume.
KICKER’s box-building guide emphasizes using the selected driver’s enclosure guidance alongside construction planning. It is useful context for keeping physical feasibility and the acoustic target connected throughout the design.
Handle Different Drivers and Inverted Mounting
The calculator’s per-driver input assumes identical physical displacement. With different drivers, calculate their occupied volumes individually and combine them in a separate worksheet rather than entering an unexamined average.
If using an average for a purely arithmetic convenience, preserve the original individual values and explain the conversion. Acoustic suitability of mixed drivers in one chamber requires its own analysis and cannot be established by their combined physical displacement.
An inverted driver places a different portion of its structure inside the cavity. A standard mounting displacement figure may therefore be inappropriate. Confirm the actual installed boundary and the manufacturer’s guidance before revising the allowance.
Mounting orientation can also affect physical clearance and the enclosure opening. The fact that a design saves internal volume does not establish that the mechanical installation or acoustic arrangement is otherwise suitable.
Check Uncertainty Before Chasing Decimal Places
An exact calculator result is only as accurate as the input geometry and displacement data. Panel thickness variation, complex internal objects, and ambiguous source conventions can exceed the last few displayed decimal places.
For the example, if each driver’s physical displacement were uncertain by 0.1 L, the two-driver allowance could vary by 0.2 L when both uncertainties act in the same direction. Keep that uncertainty visible rather than reporting a gross target as a perfect measurement.
Do not compensate for missing displacement data with an arbitrary cone-size percentage. Request the relevant specification or document a geometry estimate and evaluate whether its uncertainty matters to the chosen alignment.
Retain the net target source, installed driver count and mounting convention, physical displacement source, other internal-object calculations, gross target, and final dimensioned drawing. Before construction, check that the drawing’s actual cavity reproduces the budget and accommodates every installed component.