How to Calculate a Bandpass Crossover for a Midrange

Calculate a midrange bandpass crossover from a defined circuit and two electrical edge frequencies. For a series capacitor and series inductor feeding a resistive driver model, solve both parts together so the completed branch reaches its specified lower and upper minus-3-dB edges.

Open the Bandpass Crossover Calculator.

How to Calculate a Bandpass Crossover for a Midrange

A midrange driver needs low-frequency attenuation to limit unwanted bass and high-frequency attenuation to hand over to the tweeter. Those two requirements define a band rather than one crossover frequency.

The calculator uses one specific ideal topology: a capacitor, inductor, and resistive load connected in series, with output measured across the load. Its component selector reports the inductor in millihenries or the capacitor in microfarads. These values belong to the same interacting circuit.

This is not a universal recipe for all midrange crossovers. A buffered active high-pass followed by a low-pass, a higher-order passive network, and a series RLC branch have different transfer functions. State the topology before using a formula or interpreting a corner frequency.

The resistive load is also an approximation. A real driver’s impedance and acoustic response vary with frequency. The calculated circuit is a useful starting model, while the complete loudspeaker requires measurement-based design and appropriate driver protection.

Define the Two Edges and the Intended Driver Band

Choose a lower electrical edge fL and an upper electrical edge fH, both in hertz, with fH greater than fL. In this model, each edge is a point where load voltage is approximately 0.707 of the branch’s ideal maximum voltage, corresponding to −3.01 dB.

Start from the driver manufacturer’s usable-band and crossover guidance. A lower edge near the driver’s resonance may provide inadequate excursion control, especially with gentle stopband slopes. A high upper edge may expose breakup or inappropriate directivity even when the driver still produces measurable sound.

The electrical edge specification must not be mistaken for the desired acoustic crossover between drivers. The final acoustic response combines the circuit transfer function with the midrange’s natural behavior, enclosure, baffle, and interaction with neighboring drivers.

Record whether your input frequencies are educational test values, provisional electrical targets, or values derived from an actual acoustic design. A convenient pair of numbers entered into the tool does not establish that an unspecified midrange can operate appropriately between them.

Use the Series-RLC Transfer Function

At frequency f, the inductor has reactance XL = 2πfL, while capacitor reactance magnitude is XC = 1/(2πfC). In series, their reactive contributions oppose one another.

The load-voltage magnitude ratio is:

|H(f)| = R/sqrt[R² + (2πfL − 1/(2πfC))²]

The output is greatest when the reactive terms cancel. At that resonance, an ideal voltage source and lossless components give a load-voltage ratio of one. Real winding resistance and other losses reduce that maximum.

At either minus-3-dB edge, the magnitude of net reactance equals R. The lower edge has negative net reactance and the upper edge positive net reactance. Solving those two conditions together gives the component equations used by the calculator.

The University of Mississippi’s AC-filter laboratory material sets out the underlying series-RLC reactance model. The formulas here use the complete series circuit rather than assuming its capacitor and inductor behave as isolated filters after connection.

Calculate Each Component from the Bandwidth

Define bandwidth in hertz as B = fH − fL. Then calculate the series inductor as L = R/[2π(fH − fL)] in henries.

The series capacitor is C = (fH − fL)/(2πR fL fH) in farads. Multiply L by 1,000 for millihenries and C by 1,000,000 for microfarads.

Both edge frequencies appear in the calculation. Do not calculate an isolated high-pass capacitor using fL and an isolated low-pass inductor using fH, then claim the completed series RLC branch has those exact minus-3-dB edges. Once connected, the reactances interact.

Enter the intended edges and the load model, then select each component separately. Keep its unit alongside the result. Adding capacitor and inductor values together has no physical meaning, even if a spreadsheet permits adding their numeric cells.

Worked Example: A 600 to 3,600 Hz Electrical Band

Assume an illustrative 8-ohm resistive load with lower and upper electrical edges of 600 Hz and 3,600 Hz. The bandwidth is 3600 − 600 = 3000 Hz.

The series inductor becomes 8/(2π × 3000) henries, or approximately 0.424413 mH. The series capacitor becomes 3000/(2π × 8 × 600 × 3600) farads, or approximately 27.631067 microfarads.

Select the inductor result in the calculator and record approximately 0.424413 mH. Select the capacitor result and record approximately 27.631067 microfarads. Both results use the same edge and resistance inputs.

Check the lower edge independently. At 600 Hz, the chosen inductor and capacitor produce net reactance of approximately −8 ohms. The voltage ratio is therefore 8/sqrt(8² + 8²) = 0.7071, which is −3.01 dB.

At 3,600 Hz, net reactance is approximately +8 ohms, giving the same magnitude ratio. This verifies both requested edges without treating the components as independent first-order sections.

Locate the Center Frequency Correctly

The ideal resonant center is the geometric mean of the edges: f0 = sqrt(fL × fH). For the example, sqrt(600 × 3600) is approximately 1,469.69 Hz.

The arithmetic midpoint, 2,100 Hz, is not the resonant center of this circuit. At approximately 1,469.69 Hz, the ideal reactances cancel and load-voltage ratio reaches one. At 2,100 Hz, the example’s ratio is about 0.9417, below that maximum.

Frequency in the example Net reactance Ideal load-voltage ratio Interpretation
300 Hz −18.4 ohms 0.3987 Below lower edge
600 Hz −8.0 ohms 0.7071 Lower −3.01 dB edge
1,469.69 Hz Approximately 0 1.0000 Ideal resonant center
3,600 Hz +8.0 ohms 0.7071 Upper −3.01 dB edge
7,200 Hz +18.4 ohms 0.3987 Above upper edge

The example is symmetric in frequency ratio around its center, not in equal linear-hertz offsets. This is one reason a logarithmic frequency plot is useful for viewing crossover behavior.

Its circuit Q is f0/B, approximately 0.4899. That number describes this ideal bandpass shape and should not be confused with a driver’s mechanical or total Q parameter. The symbols describe different physical models.

Compare Edge Targets with Simple Section Estimates

An isolated first-order high-pass section calculated at 600 Hz into 8 ohms would use approximately 33.16 microfarads. An isolated first-order low-pass at 3,600 Hz would use approximately 0.3537 mH.

Those values differ from the solved series-RLC pair because the design requirement differs. The calculator’s 27.63-microfarad and 0.4244-mH values are chosen together to establish the complete branch’s specified edges.

This distinction matters when comparing calculator outputs or copying a schematic. Two tools can report different values without either being wrong if they implement different topologies or define corner frequencies differently. Ask what circuit is modeled and where the output is measured before comparing numbers.

Georgia State University’s crossover-network overview distinguishes the woofer, tweeter, and bandpass roles of components. The circuit arrangement remains part of the specification, not an optional detail that can be supplied after calculating values.

Include Component Losses and the Real Driver

Inductor winding resistance adds series loss and changes the branch behavior. Capacitor tolerance shifts the actual capacitance, and its losses and voltage suitability must also be checked. A nominal component value alone does not specify a suitable physical part.

For a real loudspeaker, replace the constant R model with measured complex driver impedance in a suitable simulation. Include the actual baffle and driver acoustic response when predicting the sound output. A corrected electrical response is not sufficient if the driver has unsuitable distortion or radiation behavior in the chosen band.

Do not infer a safe midrange input power from these L and C results. The driver still receives some out-of-band energy, and gentle filtering may leave significant excursion demands below the lower edge. Use the driver’s documented limits and appropriate system design.

Verify the Bandpass in the Complete Loudspeaker

Measure the filtered midrange alone, then its combination with the woofer and tweeter using consistent microphone position and timing reference. Check both transition regions, not just the middle of the passband.

Review the system’s impedance curve and off-axis response as well as its main-axis amplitude. Level mismatch, polarity choices, physical spacing, and driver phase affect summation. A bandpass that meets its electrical edge targets can still integrate poorly with adjacent drivers.

Keep the schematic, edge definitions, resistance assumption, calculated components, practical part values, and measured response together. When revising one edge or changing a driver, recalculate the interacting pair and recheck both crossover regions rather than assuming the other edge remains unaffected.

Table of contents