Choose a subwoofer crossover inside a range where the main speakers and subwoofer can both meet the required acoustic response and output, then verify their combined level and phase at the listening area. Main-speaker extension provides a starting clue, but one F3 number cannot determine the complete integration.
Open the Subwoofer Crossover Calculator.
How to Choose a Subwoofer Crossover Frequency
Review the main speakers’ low-frequency response and output limits, the subwoofer’s useful upper range, placement, and the bass-management system’s actual filters. The objective is a suitable acoustic transition rather than one universally correct frequency.
The calculator multiplies main-speaker F3 by heuristic factors for cabinet category, room category, preference, and nominal low-pass slope. Its output is a trial frequency, not a measured optimum or a verified acoustic alignment.
Use the suggestion to organize candidate tests. A label such as “tower,” “tight bass,” or “large room” cannot replace the actual response and timing data that determine how the system combines.
Keep the main high-pass, subwoofer low-pass, level, delay, polarity, and any separate LFE filter settings visible. Several controls may contain frequency values while performing different jobs.
Understand What Main-Speaker F3 Does and Does Not Mean
F3 commonly identifies a point 3 dB below a stated reference level under specified measurement conditions. It does not describe the complete roll-off shape, maximum clean output, or installed-room response.
Two mains with the same F3 can have different slopes and phase behavior below that point. Sealed, vented, equalized, and actively protected products can also behave differently near their lower operating limits.
The manufacturer’s measurement may describe a particular axis or environment. Room boundaries and seat location can alter the installed response, especially in the bass.
Do not assume a main speaker can maintain its low-level extension at every required output level. Excursion, compression, thermal limits, and internal protection can reduce usable output before a simple frequency-response specification suggests a problem.
Use F3 as one item in the design record. The relevant candidate band should also allow useful overlap with the subwoofer under the intended operating condition.
Distinguish Bass Management From an LFE Filter
Bass management routes selected low-frequency content from main channels to the subwoofer and can high-pass the main speakers. The dedicated LFE channel is a separate program channel with its own handling requirements.
Genelec’s bass-management explanation describes main-channel low-frequency routing and the separate LFE contribution. This distinction prevents a system’s LFE low-pass control from being mistaken for the crossover between the mains and subwoofer.
A subwoofer’s local low-pass control can also interact with a receiver’s bass-management low-pass. Cascading filters unintentionally changes the response and phase rather than merely repeating the same frequency label.
Follow the actual equipment’s connection and control instructions. If a mode bypasses a local filter, document that state. If both filters remain active intentionally, include both in the integration model.
Also confirm whether the mains are actually high-passed. Adding a low-passed subwoofer to full-range mains creates a different overlap from a defined complementary high-pass/low-pass crossover.
Use the Calculator to Generate a Candidate
Assume hypothetical mains have a documented 65 Hz F3. Selecting bookshelf, medium room, balanced preference, and 24 dB-per-octave slope gives:
65 × 1.4 × 1.1 × 1 × 1 × 1 = 100.1 Hz
The displayed result is approximately 100 Hz. It follows the calculator’s multipliers; it is not evidence that 100 Hz is optimal for every speaker with that F3.
Treat nearby supported settings such as 80, 100, and 120 Hz as candidates only if the actual main and subwoofer data support that region. Check the processor’s available filter choices and the intended output requirement.
Record why each candidate is included. For example, one may relieve more main-speaker bass demand while another may offer a better measured transition or localization behavior in the particular installation.
Do not select “movies” or “music” merely to force a desired number. The physical response and operating conditions remain the evidence for the final choice.
Compare Electrical Labels With Acoustic Targets
An electrical filter works with the speaker’s natural response to produce an acoustic branch. A filter labeled 24 dB per octave does not guarantee the installed loudspeaker follows an ideal fourth-order acoustic target.
As a defined mathematical example, ideal fourth-order Linkwitz-Riley magnitude branches can be written with x = f/fc as LP = 1/(1+x⁴) and HP = x⁴/(1+x⁴).
At a hypothetical 100 Hz acoustic crossover:
| Frequency | Ideal low-pass magnitude | Ideal high-pass magnitude |
|---|---|---|
| 70 Hz | 0.806387 | 0.193613 |
| 100 Hz | 0.500000 | 0.500000 |
| 140 Hz | 0.206543 | 0.793457 |
Each branch is −6.02 dB at the crossover. Their intended sum also depends on the defined phase relationship. These values describe that ideal alignment, not a prediction that the calculator’s trial setting will create it.
Room EQ Wizard’s equalizer documentation distinguishes target filtering and natural loudspeaker roll-off. Apply the actual branch responses rather than assuming the control label alone establishes the acoustic shape.
Measure the Individual Paths and Their Sum
Measure the mains and subwoofer separately at the same microphone location with a common timing reference. Preserve the processing, level, and crossover state for each comparison.
Then measure their combined output. Inspect the region around the candidate crossover for the intended transition, avoiding a large hump or cancellation that an individual trace may not reveal.
Use a suitable frequency range and resolution. Excessive smoothing can hide relevant interaction, while a single tone cannot describe the entire transition.
Repeat at representative seats if the design serves a listening area. A setting optimized for one point may worsen other positions because the room and relative paths vary spatially.
Keep the main-speaker and subwoofer levels separate from the timing adjustment. Changing level to conceal a cancellation can leave the underlying phase relationship unresolved.
Check Delay, Polarity, and Placement
A path difference creates a frequency-dependent phase difference. At an explicitly assumed sound speed of 343 m/s, a 0.5 m propagation difference corresponds to approximately 1.4577 ms.
At 100 Hz, that pure delay represents about 52.48 degrees of phase change. This example shows why a modest distance difference can affect the crossover region even when both paths have adequate magnitude.
The full difference may also include DSP and filter behavior. A tape measurement alone cannot establish the complete acoustic timing relationship.
Genelec’s subwoofer integration guidance discusses the need for useful main/subwoofer overlap and phase adjustment at the crossover. Apply the relevant equipment’s own procedure rather than treating one generic delay value as an alignment.
If the available controls cannot produce a useful transition, reconsider placement, routing, filtering, or the candidate frequency. A frequency change can help, but it should be evaluated through the actual combined response.
Verify Output Capability and Keep the Final Settings
After obtaining the intended low-level response, check the system’s behavior at the required operating condition using the appropriate method. Main-speaker excursion, subwoofer limits, compression, and protection can affect the practical choice.
A higher crossover can relieve some main-speaker bass demand, but it can also change subwoofer workload, localization, and spatial coverage. A lower crossover can require more output from the mains. Neither direction is universally superior.
Record the main response source, candidate rationale, filter types and settings, local subwoofer-control state, levels, delay, polarity, microphone positions, and combined-response results.
Repeat the relevant verification after moving the subwoofer, changing processor modes, or altering the mains. The final frequency should remain connected to the measured integration and output objective rather than to a heuristic multiplier applied once to F3.