How to Calculate the Impedance of Two Subwoofers

Calculate the impedance of two subwoofers by first identifying each completed driver’s nominal impedance, then applying series addition or the parallel reciprocal formula. For dual-voice-coil models, combine the coils within each subwoofer before combining the two drivers on one channel.

Open the Subwoofer Impedance Calculator.

How to Calculate the Impedance of Two Subwoofers

Two subwoofers do not have one inevitable combined impedance. The result depends on whether their coils are single or dual, the nominal impedance of each coil, and how the completed drivers connect to the amplifier.

For two identical completed drivers of nominal impedance Z, series connection gives 2Z, while parallel connection gives Z/2. Those equations apply only after the per-driver configuration is known.

A pair of single-4-ohm subwoofers therefore gives 8 ohms in series or 2 ohms in parallel. A pair of dual-4-ohm subwoofers offers different options because each driver contains two nominal 4-ohm coils that must also be connected appropriately.

Use the manufacturer’s nominal ratings for this planning calculation. The electrical impedance seen by an amplifier varies with frequency, so the combined nominal number does not establish a fixed resistance or every operating demand.

Separate the Driver Label from the Final Load

Write a short inventory before drawing the circuit: exact model, coil impedance, coil count, number of drivers, and the channel they will use. This prevents an enclosure’s external label from being confused with an individual internal coil specification.

If you have a prewired enclosure, its terminals may already present a completed nominal load. Find the enclosure wiring information before applying another assumed series or parallel operation to its label.

For bare dual-coil drivers, identify which terminals belong to each winding. Some use standard terminal pairs, while others provide configuration tabs or jumpers. The intended connections come from the model’s drawing, not from a generic assumption about terminal position.

Both drivers must match the uniform model used by the calculator. Different impedance versions, different coil configurations, or unlike drivers require an explicit network calculation and a suitable system design. A simple average of their labels is not a valid substitute.

Apply Series or Parallel Arithmetic to the Pair

In series, the same current passes through the two completed driver networks. Their nominal impedances add: Zseries = Z1 + Z2.

In parallel, both completed drivers connect across the channel voltage. Use Zparallel = Z1Z2/(Z1 + Z2). For equal values, this simplifies to half the impedance of either driver.

Do not mistake the physical route of a cable for the electrical arrangement. A cable running from amplifier to one enclosure and then to the next can create a parallel circuit if the link terminals are internally connected to the same positive and negative nodes.

Likewise, two terminal pairs on a mono amplifier can be internally parallel. Connecting a subwoofer to each pair may still put both on one output stage. Check the amplifier documentation before treating them as two independent channels.

Kicker’s series and parallel wiring note illustrates the underlying connections. The electrical nodes determine the topology, regardless of whether the cable arrangement looks like a line or a branching tree.

Work Through the Dual-Coil Stage First

For each dual-coil driver with two equal coils Zc, series coils give 2Zc per driver and parallel coils give Zc/2 per driver. Then apply the two-driver connection to those completed values.

For two dual-4-ohm drivers, series coils make each driver 8 ohms. Putting those two drivers in parallel gives 4 ohms total. Parallel coils make each driver 2 ohms, and putting those two in parallel gives 1 ohm total.

Series-connected completed drivers are additional arithmetic options where supported by the intended design. Two 8-ohm completed drivers in series give 16 ohms, while two 2-ohm completed drivers in series give 4 ohms.

Keep both configuration decisions on the drawing. Writing only series-parallel without identifying which stage is series and which is parallel can hide a very different load. Label coil connections and driver connections separately.

Use the Calculator for a Matched Pair

Enter nominal impedance per coil and choose single or dual voice coils. Set driver count to two, then choose the coil wiring and completed-driver wiring that match the proposed drawing.

For single-coil drivers, the coil-wiring choice does not change the one-coil result. For dual-coil drivers, it changes the intermediate load substantially. Record that per-driver value before accepting the final combined output.

The calculator assumes both drivers use the same coil configuration. It does not independently represent one series-wired dual-coil driver and one parallel-wired dual-coil driver. Do not enter a fictitious average impedance to make an unlike arrangement fit its fields.

Use the result to review the nominal channel load, then read the amplifier manual for the actual mode. The calculator does not know the amplifier’s minimum load, its protection behavior, or its continuous output specification at the resulting impedance.

Worked Example: Two Dual-4-Ohm Drivers at 4 Ohms Total

Assume an illustrative pair of identical dual-4-ohm subwoofers. The intended arrangement uses series coils within each driver and connects the two completed drivers in parallel on one channel.

Each driver has nominal impedance 4 + 4 = 8 ohms. The pair gives (8 × 8)/(8 + 8) = 4 ohms. Enter 4 ohms per coil, dual coils, two drivers, series coil wiring, and parallel completed-driver wiring to reproduce the result.

As a separate resistive power illustration, assume 20 V RMS is maintained across the completed 4-ohm network. Total modeled power is 20²/4 = 100 W. Each equal 8-ohm driver branch receives 50 W.

Within each driver, the equal series coils share voltage. Each coil receives 10 V RMS and 10²/4 = 25 W in the resistive model. Four coils at 25 W each sum to the network’s 100 W.

This does not establish the speakers’ permissible power or guarantee that an amplifier maintains that voltage. It checks the network bookkeeping under an explicit fixed-voltage assumption. Actual power varies with the signal and real impedance.

Compare Two-Subwoofer Options

The table distinguishes single-coil and dual-coil labels and states the internal coil arrangement before combining the pair.

Two identical subwoofers Per-driver coil arrangement Each completed driver Pair in parallel Pair in series
Single 4-ohm One coil 4 ohms 2 ohms 8 ohms
Single 8-ohm One coil 8 ohms 4 ohms 16 ohms
Dual 2-ohm Coils in series 4 ohms 2 ohms 8 ohms
Dual 2-ohm Coils in parallel 1 ohm 0.5 ohm 2 ohms
Dual 4-ohm Coils in series 8 ohms 4 ohms 16 ohms
Dual 4-ohm Coils in parallel 2 ohms 1 ohm 4 ohms

This is a comparison of nominal circuit arithmetic. It is not a statement that every listed connection is suitable for the drivers or supported by an available amplifier. Follow the manufacturer’s intended diagrams and operating conditions.

The JL Audio TW3 manual provides model-specific multiple-driver examples and identifies both-coil requirements. Use its approach of matching the diagram to the exact impedance version, rather than generalizing its individual product limits.

Check Amplifier Mode and Measurement Meaning

Compare the final nominal load with the amplifier’s minimum for the chosen channel mode. A bridge-mode limit can differ from the ordinary single-channel limit. A stereo total or a brief dynamic rating does not automatically establish support for continuous operation at that load.

If the calculated load is too low, revise the supported connection or equipment selection. Do not use a gain-control position as evidence that an unsupported load has become compatible. Output demand changes with signal, and the connection itself remains the same.

A DC resistance reading can help verify continuity but should not be expected to equal the nominal load exactly. Driver winding resistance, leads, and contacts affect the reading, while the nominal label describes an AC impedance class rather than that one DC value.

Power the system down before inspecting or changing wiring. Trace the completed connections against the schematic, check terminal polarity and secure connections, and retain the final nominal load with the amplifier-mode reference. Recalculate if either subwoofer or its internal configuration changes.

Table of contents