Calculate amplifier efficiency by dividing matched average electrical output power by total electrical input power and multiplying by 100. For a resistive test load and a steady DC supply, output is Vrms²/R and supply input is Vdc × Idc.
Open the Amplifier Efficiency Calculator.
How to Calculate Amplifier Efficiency
The basic relationship is:
Amplifier efficiency, % = 100 × average output watts ÷ average input watts
Choose one measurement boundary and one operating condition. For an amplifier stage measured at its DC supply terminals, the denominator is the total power entering those terminals. If the boundary instead includes an AC power supply, wall-input power must include that supply’s losses.
The calculator uses RMS output voltage and a stated load resistance to estimate output power, then divides by the product of DC supply voltage and current. This assumes a suitable resistive output load and a sufficiently steady or appropriately represented DC input.
It does not identify a universal efficiency for an amplifier class. Real efficiency depends on output level, load, signal, supply conditions, frequency, and which auxiliary circuits are included.
Keep efficiency separate from voltage gain and acoustic sensitivity. Those describe different relationships and cannot be substituted for electrical output divided by input.
Define the Input and Output Boundaries
Specify whether the test includes only the power-output stage, the complete amplifier electronics, or the entire mains-powered product. Do not compare output from the whole product with input measured at only one of several supplies.
For a steady single DC source, input power is voltage multiplied by current. If voltage or current varies significantly, average instantaneous input power is the relevant quantity; multiplying two independently averaged readings is not always equivalent.
For multiple DC rails, sum the power entering all the rails on a consistent sign convention. Do not subtract the magnitude of a negative rail from a positive rail and conclude that two active supplies deliver zero power.
For example, two illustrative 35 V-magnitude rails each delivering 1 A represent 70 W combined input when those current directions correspond to power entering the amplifier. The particular wiring and instrument convention still need to be understood.
The calculator presents a single voltage/current product. Use it directly for a valid single-source boundary. For multiple supplies, calculate the matched total input independently rather than entering one rail and ignoring the others.
Determine Output Power on the Correct Load Model
For a purely resistive test load, average output power is RMS load voltage squared divided by resistance. Measure the voltage across the complete load, using an instrument and method appropriate to the output signal.
TI’s audio-amplifier gain report explains the RMS-voltage power relationship. A peak or peak-to-peak reading must not be entered as RMS without the appropriate waveform-based conversion.
An actual loudspeaker is a frequency-dependent complex load. Dividing voltage squared by its nominal impedance is a simplified estimate, not a complete real-power measurement across every operating condition.
With a reactive load, average real power requires the voltage/current relationship over time. For a sinusoid, phase matters; for more general signals, an appropriate average of instantaneous voltage times current is needed.
Switching-amplifier content can also complicate readings. Use suitable bandwidth, filtering, loading, and measurement procedures rather than assuming every AC meter reports the wanted audio-output RMS value accurately.
Work Through a Matched Efficiency Example
Consider an illustrative test with 20 V RMS across an 8-ohm resistive load. The matched steady DC source supplies 35 V at 2 A under that same condition.
Output power is:
20² ÷ 8 = 50 W
Input power is:
35 × 2 = 70 W
Efficiency is therefore:
100 × 50 ÷ 70 = approximately 71.43%
Enter output voltage 20, load eight, supply voltage 35, and supply current two in the calculator. The result should be approximately 71.43%.
The difference between matched input and output is 20 W on this boundary. It represents electrical power not delivered to the stated load, including the losses and any auxiliary consumption included in the measurement.
These numbers are a hypothetical arithmetic example, not a measured specification for a commercial amplifier. The calculation is meaningful only if the output and input observations represent the same signal and operating interval.
Compare Efficiency Across Output Levels
An amplifier’s efficiency is generally not a single constant over its entire operating range. Quiescent and auxiliary consumption can become a larger fraction of input at low output, while other losses change with current and operating conditions.
For illustrative matched power readings:
| Output power | Total input power | Efficiency | Input minus output |
|---|---|---|---|
| 10 W | 20 W | 50.00% | 10 W |
| 50 W | 70 W | 71.43% | 20 W |
| 100 W | 125 W | 80.00% | 25 W |
These rows are separate scenarios, not the measured curve of one named device. They show why a higher percentage does not necessarily mean fewer watts of heat or lower absolute input power.
In the last row, efficiency is higher than in the first, yet the input-output difference is larger. Thermal planning needs the actual loss power and operating pattern, not just the percentage.
When comparing devices, hold output power, load, signal, and boundary consistent. Comparing one amplifier near high output with another at idle does not isolate a meaningful efficiency difference.
Avoid Double-Counting Class and Power-Supply Losses
Once actual output and input power are measured on the chosen boundary, their ratio already includes that boundary’s losses. Multiplying the result by an additional generic Class D or Class AB efficiency factor would count another assumed correction on top of the measurement.
TI’s amplifier measurement guidance discusses appropriate power measurements for different output stages and loads. Use the applicable procedure rather than treating a topology label as a substitute for measured operating data.
Similarly, a DC-terminal efficiency does not include an upstream supply’s losses unless that supply is within the measured boundary. If 70 W enters an amplifier from a supply drawing 80 W at the wall, a 50 W output represents 71.43% amplifier-stage efficiency but 62.5% wall-to-load efficiency.
Both percentages can be valid when labelled correctly. Their difference reflects the changed input boundary, not a contradiction in the arithmetic.
Do not mix an output rating, an unrelated idle-current measurement, and a nominal supply voltage to create a claimed measured efficiency. Use simultaneous or suitably matched observations.
Interpret Zero and Impossible Results
Positive input power with zero useful output gives zero efficiency on this definition. That can describe an idle state, but it does not imply zero electricity consumption. Idle watts remain relevant to a battery or energy budget.
Zero input makes the ratio undefined. Check disconnected measurements, instrument range, sign conventions, and whether a required supply was omitted. The calculator cannot produce a meaningful ordinary efficiency percentage from a zero denominator.
An apparent result above 100% indicates inconsistent inputs or a boundary/measurement problem in this amplifier calculation. Investigate waveform definitions, reactive-load assumptions, supply accounting, measurement timing, and instrument response instead of treating the result as excess energy production.
At very low output, measurement uncertainty can dominate the percentage. Keep the original readings and instrument conditions with the calculation so an implausible ratio can be traced back to its inputs.
Use Efficiency in an Audio Power Budget
For an explicitly assumed operating efficiency, required input power is output power divided by efficiency as a fraction. A hypothetical 50 W output at 0.714286 efficiency requires approximately 70 W input.
This inversion is useful for a scenario, but an efficiency measured at one output level may not represent music playback at a different average level. Use a representative operating profile or direct input-energy measurement when the goal is runtime or electricity consumption.
Keep power and energy distinct. Input watts multiplied by matched hours gives watt-hours; a percentage by itself contains no runtime information. Include standby and other loads either in the measured total or as separate non-overlapping terms.
For battery use, representative voltage, usable capacity, discharge rate, and cutoff behaviour remain additional inputs. A correct amplifier efficiency ratio does not determine a battery’s permitted discharge limit or its actual usable energy.
Questions About Amplifier Efficiency
Is amplifier efficiency the same as speaker efficiency?
No. Amplifier efficiency compares electrical load output with electrical supply input. Loudspeaker conversion efficiency concerns acoustic output relative to electrical input, and sensitivity is another separately defined acoustic reference.
Does 80% efficiency always mean the amplifier wastes 20 W?
No. Loss watts depend on input power. At 100 W input, 80% implies 80 W output and a 20 W difference. At 200 W input, the same percentage implies a 40 W difference.
Can I use a music signal instead of a sine wave?
The energy relationship still applies, but input and output must be measured with suitable methods over the same interval and boundary. Do not assume a fixed sine-wave crest factor or use mismatched average readings.