How to Calculate a Woofer Crossover Inductor

For an ideal first-order woofer low-pass, calculate the series inductance with L = R/(2 pi fc) after establishing the actual load downstream of that inductor. Convert henries to millihenries explicitly, and treat nominal impedance as a resistive starting model rather than the driver’s complete audio-frequency load.

Open the Woofer Low Pass Calculator.

How to Calculate a Woofer Crossover Inductor

Define a series inductor feeding a woofer load, with output voltage measured across the load. This topology is the basis of the calculator’s first-order electrical model.

The tool supports an already-combined load, identical drivers all in series, or identical drivers all in parallel. Driver count is ignored when the entered load already represents the complete downstream network.

It does not calculate higher-order crossover sections or include inductor winding resistance. Real driver impedance, losses, acoustic response, and component operating limits require separate evaluation.

Use the formula to obtain a traceable starting value, then verify the actual circuit and loudspeaker rather than treating the millihenry result as a finished design.

Derive the First-Order Inductance

For a resistive load R and ideal series inductor L:

H = R/(R + j omega L)

The voltage magnitude reaches 1/sqrt(2) of the ideal low-frequency passband when inductive reactance equals resistance: omega L = R.

Since omega = 2 pi f, the corner relationship is:

Lhenries = R/(2 pi fc)

Multiply by 1,000 for millihenries. The calculation is for the stated first-order section, not a generic inductor position in every crossover topology.

Georgia State University’s crossover reference illustrates the series-inductor low-pass role. Real loudspeakers add their own impedance and acoustic behavior to that electrical starting model.

Establish the Downstream Load Before Entering It

If one woofer is fed by its own inductor, use that driver’s relevant load model. If a shared inductor feeds several drivers, reduce the actual network first.

For two identical nominal 8-ohm drivers in parallel, the nominal combined load is 4 ohms. In series, it is 16 ohms.

The calculator can perform those all-series or all-parallel reductions when you enter the per-driver value and count. For a more complex group, calculate the network separately and select already-combined load.

KICKER’s wiring paper illustrates the nominal series and parallel relationships. Preserve the actual connection diagram with the inductor calculation.

Do not enter 4 ohms as an already-combined parallel load and then divide it by the two-driver count again. The tool’s already-combined choice prevents that duplication by ignoring count for that mode.

Work Through a Two-Woofer Example

Assume two hypothetical nominal 8-ohm woofers connected in parallel after one shared inductor. Their resistive planning model is 4 ohms, and the selected ideal electrical corner is 650 Hz.

Required inductance is:

L = 4/(2 pi × 650) ≈ 0.000979415 H

L ≈ 0.979415 mH

Enter 8 ohms per driver, two drivers, and parallel mode. Alternatively, select already-combined load and enter 4 ohms; both describe the same nominal model.

For the same two drivers in series, the nominal 16-ohm load requires approximately 3.917660 mH at 650 Hz. One 8-ohm load requires approximately 1.958830 mH.

Combined resistive load at 650 Hz Ideal series inductance
4 ohms 0.979415 mH
8 ohms 1.958830 mH
16 ohms 3.917660 mH

These are electrical examples, not proof that 650 Hz is an appropriate acoustic crossover for unspecified woofers or their companion driver.

Check Henry, Millihenry, and Microhenry Units

One henry equals 1,000 millihenries, and one millihenry equals 1,000 microhenries. The example can therefore be written as 0.000979415 H, 0.979415 mH, or approximately 979.415 µH.

Those are the same inductance. Writing the henry result as though it were already in millihenries creates a factor-of-1,000 error.

As an independent check, reactance at the corner is 2 pi × 650 × 0.000979415 ≈ 4 ohms, matching the intended load resistance.

Keep units in the schematic and parts list. A number such as 0.98 without H, mH, or µH is not a complete component specification.

When comparing catalog values, verify both the unit and decimal placement rather than relying on a similar-looking printed number.

Examine Frequency and Load Sensitivity

At fixed resistance, required inductance is inversely proportional to the selected corner. For the 4-ohm model, 500 Hz requires approximately 1.273240 mH, while 1,000 Hz requires approximately 0.636620 mH.

At fixed corner, inductance is directly proportional to resistance. If a nominal 8-ohm driver is actually represented by a 6-ohm resistive approximation at the relevant condition, 650 Hz would imply approximately 1.469123 mH rather than 1.958830 mH.

That comparison shows sensitivity to the load assumption; it does not recommend replacing a real impedance curve with one chosen resistance. The actual reactive load requires a suitable circuit model.

Nominal impedance is useful for a starting estimate, but it does not capture resonance, inductive rise, enclosure loading, or compensation networks.

Use measured or manufacturer impedance data when refining the design beyond the introductory calculation.

Include Actual Coil Resistance and Construction

An inductor has DCR as well as inductance. In the simple circuit, total series denominator becomes R + rDCR + j omega L, reducing the low-frequency voltage delivered to the driver.

Suppose the 4-ohm model uses a hypothetical actual 1 mH coil with 0.25-ohm DCR. Low-frequency voltage ratio is 4/4.25 ≈ 0.941176.

Its corner relative to that reduced passband is (4 + 0.25)/(2 pi × 0.001) ≈ 676.4085 Hz. That differs from the lossless corner and the original target.

Jantzen’s coil catalog lists inductance and DCR separately with construction details. Treat them as separate design attributes rather than assuming every coil of the same millihenries is interchangeable.

Review current, thermal behavior, core characteristics where applicable, dimensions, and layout. A calculated nominal value does not establish the coil’s suitability for the intended output.

Evaluate Tolerance Before Final Assembly

A nominal inductance can differ from the measured part. For a hypothetical 1 mH coil with ±5% inductance tolerance, the possible nominal endpoints are 0.95 and 1.05 mH.

Ignoring DCR for this isolated comparison, a 4-ohm first-order model gives corners of approximately 670.1261 Hz and 606.3045 Hz at those endpoints. The inverse relationship makes the frequency variation slightly asymmetrical.

This range does not include driver variation, winding resistance, or the rest of a real crossover. Use actual measured component properties where the design needs closer matching, and retain the measurement conditions and uncertainty with the parts record.

Distinguish Shared and Individual Inductors

Two drivers can share one inductor before their parallel split, or each can have a separate branch inductor. Those arrangements have different component currents and practical losses.

If each nominal 8-ohm driver has its own ideal 650 Hz section, each branch uses approximately 1.958830 mH. The shared-coil nominal model uses approximately 0.979415 mH for the combined 4-ohm load.

The ideal relationships can be analyzed, but real DCR, driver variation, and branch interaction need the actual schematic. Do not substitute one arrangement for another without reviewing those differences.

For dual-voice-coil drivers, establish the coil network first. The inductor’s downstream load depends on both coil and driver connections.

Verify the Electrical and Acoustic Design

Measure the complete input impedance and relevant driver voltage response using suitable equipment and the intended circuit. Then measure each acoustic branch and the combined loudspeaker with a consistent timing reference.

Check off-axis behavior, phase, driver limits, and the intended operating level. A first-order electrical corner does not guarantee a matching acoustic slope or adequate breakup suppression.

Retain load reduction, topology, target, unit conversion, ideal inductance, actual measured L and DCR, component ratings, and verification results. This keeps the woofer-inductor calculation useful without allowing a nominal millihenry value to stand in for the complete crossover design.

Table of contents