Calculate a first order speaker crossover with a series inductor for the woofer and a series capacitor for the tweeter, using each driver’s own resistive load model. The ideal electrical sections approach 6 dB per octave, while real acoustic slopes and driver protection depend on the complete loudspeaker.
Open the First Order Crossover Calculator.
How to Calculate a First Order Speaker Crossover
A basic two-way first-order electrical crossover has two parallel branches across the source. One branch contains a series inductor and the woofer load. The other contains a series capacitor and the tweeter load.
The inductor increasingly opposes current as frequency rises, producing low-pass behavior across the woofer model. The capacitor increasingly opposes current as frequency falls, producing high-pass behavior across the tweeter model.
For the ideal resistive branches, each corner occurs where the reactive component’s impedance magnitude equals its load resistance. This establishes a simple calculation, but it does not establish that unspecified drivers can share that crossover frequency or tolerate the gentle filtering.
The calculator evaluates either individual component. Keep the component selector and unit visible when recording its result. An inductor in millihenries and a capacitor in microfarads are separate parts, not values that can be summed into one crossover number.
Choose the Crossover Region Before Calculating Parts
Start with the drivers’ acoustic response, impedance, distortion, and operating guidance. Select a candidate handover region where both drivers can contribute appropriately, rather than picking a frequency solely because the formulas are easy to apply.
A tweeter’s resonance or the lowest frequency shown on a catalog graph is not necessarily a suitable corner for a first-order filter. A single capacitor continues passing some lower-frequency energy, and the tweeter may need a steeper crossover to control excursion or heating.
The woofer’s upper response matters as well. Breakup, narrowing radiation, or an uneven response can make a simple inductor insufficient even when the nominal corner calculation is correct. A first-order design is not automatically suitable because it uses few components.
Identify the intended acoustic target separately from the electrical section. The driver response and enclosure contribute to the sound reaching the microphone, so the electrical filter order is only part of the system behavior.
Use the Two Component Equations
For the woofer’s series inductor, calculate L = Rwoofer/(2πfc) in henries. Multiply by 1,000 for millihenries.
For the tweeter’s series capacitor, calculate C = 1/(2πfc Rtweeter) in farads. Multiply by 1,000,000 for microfarads. Use fc in hertz and each load model in ohms.
The resistance appears in opposite positions in these formulas. A larger load requires a larger low-pass inductor but a smaller high-pass capacitor at the same intended corner. Multiplying by resistance in both equations would be a fundamental error.
If the woofer and tweeter have different nominal impedance models, calculate them separately. Do not enter the completed cabinet’s nominal impedance as a substitute for both individual branch loads without a supporting circuit model.
Georgia State University’s crossover reference shows the component roles in the low-pass and high-pass branches. The equations apply to those particular connections, not to arbitrary inductors or capacitors placed elsewhere in a network.
Worked Example: Separate 6-Ohm and 8-Ohm Models
Assume an illustrative educational model uses a 6-ohm resistive woofer branch, an 8-ohm resistive tweeter branch, and a shared 2,000 Hz electrical corner. These values do not represent a recommended design for unspecified real drivers.
The woofer inductor is 6/(2π × 2000) henries, approximately 0.000477465 H or 0.477465 mH. Enter 2,000 Hz and 6 ohms, then choose the low-pass inductor in the calculator.
The tweeter capacitor is 1/(2π × 2000 × 8) farads, approximately 0.000009947 F or 9.947184 microfarads. Keep 2,000 Hz, change the load to 8 ohms, and select the high-pass capacitor.
Check the components independently. At 2,000 Hz, the inductor’s reactance is approximately 6 ohms, matching the woofer model. The capacitor’s reactance magnitude is approximately 8 ohms, matching the tweeter model.
Each ideal branch therefore has approximately 0.7071 voltage magnitude at its own load, or −3.01 dB relative to the source. This equality of electrical ratios does not establish equal sound output because real drivers can have different sensitivity and acoustic response.
Understand What 6 dB per Octave Means
First-order electrical filtering approaches a 6 dB-per-octave stopband slope. An octave is a doubling or halving of frequency, not a fixed number of hertz.
Near the corner, the response does not change by exactly 6 dB for each octave step. The asymptotic slope becomes a better approximation farther into the stopband. At the corner itself, the ideal attenuation is approximately 3.01 dB.
Using the ratio x = frequency/fc, the low-pass magnitude is 1/sqrt(1 + x²), and the high-pass magnitude is x/sqrt(1 + x²).
| Frequency relative to corner | Low-pass amplitude | High-pass amplitude | Example frequency with 2,000 Hz corner |
|---|---|---|---|
| fc/4 | 0.9701 | 0.2425 | 500 Hz |
| fc/2 | 0.8944 | 0.4472 | 1,000 Hz |
| fc | 0.7071 | 0.7071 | 2,000 Hz |
| 2fc | 0.4472 | 0.8944 | 4,000 Hz |
| 4fc | 0.2425 | 0.9701 | 8,000 Hz |
These are voltage magnitudes across ideal resistive loads. Convert them to decibels with 20 log10(amplitude). The table shows why neither driver is abruptly switched off at the crossover: their operating bands overlap broadly.
Include Phase When Considering the Sum
At the shared ideal corner, the low-pass output lags the input by 45 degrees and the high-pass leads it by 45 degrees. Their relative phase is therefore 90 degrees, not zero.
Adding the two 0.7071 magnitudes arithmetically gives about 1.414, but that is not the correct complex sum under these phase conditions. The ideal complementary first-order transfer functions add to unity when their amplitudes and relative phases satisfy the model.
A real acoustic sum also includes driver sensitivity, phase, acoustic centers, and path differences. Two electrically complementary branches do not guarantee flat acoustic output when the drivers have different natural responses or physical positions.
Siegfried Linkwitz’s crossover discussion emphasizes the acoustic sum and radiation behavior. Use those system requirements when evaluating a design rather than assuming a simple schematic automatically produces the textbook result.
Account for Real Impedance and Component Loss
A loudspeaker’s nominal impedance is not a constant resistance. Near resonance and at higher frequencies, the actual magnitude and phase can depart substantially from the model. Use measured complex impedance for a meaningful final simulation.
Inductor winding resistance adds series loss and can alter level and response. Capacitors have tolerance, losses, voltage limits, and physical characteristics. Choosing parts with the calculated nominal values does not specify all the component properties the design requires.
Practical rounding changes the result too. If a standard component differs from the calculation, solve its resulting ideal corner and then evaluate the complete network. Do not silently label the installed circuit with the original target as though no substitution occurred.
Additional attenuation or correction networks interact with the crossover. A tweeter series resistor or L pad changes the load presented to other components depending on its position. Include those parts in the schematic and simulation rather than calculating them as unrelated accessories.
Verify the Completed Loudspeaker
Measure the filtered drivers individually on the intended baffle, then measure their combination with a consistent timing reference. Inspect the transition region and the useful listening angles, not only one on-axis amplitude point.
Check system impedance and driver behavior under the intended operating requirements. A nominally correct first-order crossover may still provide insufficient out-of-band attenuation, unsuitable directivity, or a poor acoustic sum.
Keep the driver data, target frequencies, load assumptions, calculated parts, installed values, schematic, and measurement results together. The first-order equations then remain a transparent design reference, while the measured complete system determines whether that implementation meets the actual goal.