Calculate speaker delay from the difference between two sound-path distances to the same reference point, divided by sound speed. Delay the earlier-arriving path, and account separately for any documented difference in electronic latency.
Open the Speaker Delay Calculator.
How to Calculate Speaker Delay from Distance
For a main source farther from the chosen listener than a fill or delay source, the geometric starting point is:
Additional delay for the nearer source, ms = 1,000 × (main path − near-source path) ÷ sound speed
Use both distances in metres and sound speed in metres per second. The calculator estimates sound speed with c = 331.3 + 0.606T, where T is air temperature in degrees Celsius.
Its additional alignment offset is a separately entered positive allowance added to that geometric result. Keep zero unless you have a defined reason for the extra delay. The field does not measure processor latency or automatically optimize acoustic integration.
The comparison applies at one reference point. Moving the listener changes both paths, so a value calculated for one position does not guarantee identical arrival relationships throughout an audience area.
Measure Both Paths to the Same Reference Point
Choose a clearly identified listening or measurement position. Measure the direct acoustic path from each relevant source to that same point. Do not enter the cable route or simply the distance between the two speaker cabinets.
Cabinet separation equals the listener path difference only in particular geometries. A fill mounted to the side or at a different height can have a different direct path even when its floor-plan position looks close.
Use three-dimensional distances where height matters. Identify an appropriate acoustic reference for the sources and retain that convention in the measurement record. A cabinet’s front edge is not guaranteed to represent the effective acoustic origin at every frequency.
The Biamp PE-D60 manual explains the importance of listener-referenced path difference and temperature in delay calculations. Those measurements establish a geometric starting point rather than a complete room calibration.
Keep the reference position, source names, measured paths, temperature, and electronic settings together. That makes a later adjustment understandable when the system or audience position changes.
Calculate a 12-Metre Path-Difference Example
Consider an illustrative reference point 18 m from the main source and 6 m from the nearer fill. Air temperature is 20°C, and the additional offset is initially zero.
First calculate sound speed:
331.3 + 0.606 × 20 = 343.42 m/s
The path difference is 18 − 6 = 12 m. Geometric delay is:
1,000 × 12 ÷ 343.42 = approximately 34.94264 ms
Enter main distance 18, delay-source distance six, temperature 20, and offset zero. The calculator should display approximately 34.94 ms with its two-decimal formatting.
As an independent arrival check, the main acoustic travel time is approximately 52.41395 ms, while the near source’s travel time is approximately 17.47132 ms. Adding 34.94264 ms to the near path brings those geometric arrival times together within rounding.
This example assumes equal electronic latency and a simple direct-path propagation model. It is not a claim that every 12 m cabinet separation should use the same delay.
Account for Electronic Latency with the Correct Sign
Total arrival time contains both acoustic travel and electronic delay. For each path, write:
Arrival = acoustic distance ÷ sound speed + electronic latency
The additional delay required on the nearer fill is the main arrival minus the fill arrival. If the main electronics add 3 ms more latency than the fill electronics, the example’s required fill delay increases by 3 ms to approximately 37.94264 ms.
That positive difference can be represented by an offset of three in this calculator. The offset is an explicit addition, so document its source instead of selecting a generic room or music preset.
If the fill path already has more electronic latency, the required additional delay can decrease. A negative latency correction is not represented by this form’s positive additional-offset field; calculate the full signed arrival difference independently using the documented path latencies.
Do not add a latency figure twice if it is already included in a measured arrival-time comparison. Likewise, a deliberate localization offset is a design choice, not the same thing as compensating a known processor delay.
See How Temperature Changes the Starting Value
Holding the 12 m geometric path difference constant gives:
| Air temperature | Stated approximate sound speed | Geometric delay |
|---|---|---|
| 10°C | 337.36 m/s | 35.57 ms |
| 20°C | 343.42 m/s | 34.94 ms |
| 30°C | 349.48 m/s | 34.34 ms |
Warmer air in this approximation increases sound speed, reducing travel time for a fixed distance. The resulting delay change can matter when a system covers long paths or operates across changing conditions.
The linear approximation does not model every atmospheric variable. Humidity, wind, temperature gradients, and differing path conditions can affect propagation beyond this simple temperature entry.
Use a representative condition for the actual sound path. A temperature measured beside hot electronics may not describe the audience air through which the sound travels.
Different references may use slightly different sound-speed assumptions. Keep the stated model with the numerical result before interpreting small differences between calculators as a wiring or processor fault.
Interpret Zero and Negative Geometric Results
Equal path lengths with equal electronic latency need zero additional geometric delay. That does not prove identical phase response or identical processing; it only removes the distance difference in this model.
If the designated delay source is farther from the reference point than the main source, main distance minus delay-source distance becomes negative. Ordinary DSP delay cannot make that farther source emit sound before it receives the signal.
Reconsider which path is the timing reference and which earlier path should be delayed. The magnitude of a negative result may be useful in that reassessment, but its sign should not be discarded without identifying the corresponding physical path.
Neumann’s acoustical application FAQ describes delaying nearer loudspeakers relative to a farther reference. The reference choice makes the direction of the adjustment clear.
Retain the signed arrival calculation when electronic latency changes the expected order. Geometry alone can misidentify the earlier path if the processors differ substantially.
Verify the Result Acoustically
Measure the relevant arrival relationship with an appropriate reference signal, microphone position, and system measurement method. Keep the physical and processing setup consistent with the calculation being evaluated.
Reflections can create later arrivals that should not automatically be mistaken for the direct sound. Filters and driver behaviour can also produce frequency-dependent phase and group delay, so one broadband timing number may not describe every crossover relationship.
For main/sub integration, geometric time of flight is only part of the task. Check the acoustic response and phase behaviour through the intended handover region rather than assuming distance alignment alone produces the desired summation.
For a distributed audience system, inspect more than one relevant position. A chosen reference may balance a useful coverage region, but moving toward another source changes the direct-path difference.
Document the final delay, signal routing, reference location, and measurement conditions. Recheck after moving a cabinet or changing a processor, filter, or network path that alters latency.
Questions About Distance-Based Speaker Delay
Should I use the distance between the speakers?
Use each speaker’s direct distance to the same reference point, then subtract. Cabinet-to-cabinet separation is only equivalent in a geometry where those paths make it so.
Is one metre always three milliseconds?
At the calculator’s 20°C assumption, one metre corresponds to approximately 2.912 ms. Three milliseconds per metre is a rough mental estimate, not the exact value used by this model.
Does this align every seat?
No. The path difference changes with listener position. Select and verify a reference appropriate to the application, then assess the useful audience region and complete acoustic response.