Calculate a bandpass box’s two chambers from separate driver-specific net targets, then add only the displacement physically assigned to each chamber. Keep their individual acoustic requirements and the front port design separate; one total volume cannot define the alignment.
Open the Bandpass Box Calculator.
How to Calculate the Two Chambers of a Bandpass Box
Define the enclosure topology before using any volume formula. The calculator models a fourth-order bandpass planning arrangement with a sealed rear chamber and a vented front chamber.
It accepts independently established net targets and displacement allowances for both chambers. It reports either chamber’s gross internal cavity volume or the sum of those gross cavity volumes.
It does not derive a bandpass alignment from driver diameter or Qts alone. The driver parameters, desired response, losses, source conditions, port behavior, and operating limits require an appropriate complete model or relevant plan.
Use the tool after the acoustic targets are established. Its arithmetic supports a construction budget without pretending that a single suggested box volume describes both chambers and their tuning.
Distinguish the Sealed-Rear and Vented-Front Roles
In the defined topology, the driver separates two chambers and the front chamber couples to the outside through a port. The two cavity air loads participate differently in the complete response.
KICKER’s enclosure guide illustrates the sealed-and-vented two-chamber bandpass arrangement. Its description provides topology context; the actual design still needs a driver-specific alignment rather than a universal ratio between chamber sizes.
A design with both chambers vented is a different topology and requires its own tuning and model. Do not apply the calculator’s sealed-rear interpretation to it without changing the design framework.
The rear and front net volumes are therefore separate inputs. Their sum may help assess cabinet size, but it does not replace either input in an acoustic simulation.
Likewise, the front-port tuning is not synonymous with the system’s entire passband. The complete coupled response determines useful bandwidth, level shape, excursion, and other behavior.
Obtain Separate Acoustic Targets First
Use the exact driver’s relevant parameters and a suitable enclosure model or manufacturer plan. Review more than a low-level response curve: source voltage, filtering, excursion, heating, losses, and port flow can constrain the design.
Preserve the target definitions and model conditions. A sealed rear target from one design and a front target borrowed from another do not automatically combine into a valid alignment.
Nominal diameter cannot determine the two volumes. Qts alone also omits essential compliance, resonance, and other driver behavior needed for an acoustic design.
If a complete published plan supplies construction dimensions, determine whether displacement is already included. Do not increase its chamber volumes by applying the same allowances a second time.
For a new net-target calculation, proceed to a chamber-by-chamber physical ledger so the required air spaces survive the construction process.
Assign Physical Displacement to Each Chamber
The driver can occupy portions of both chambers. Assign each installed portion to the cavity it actually occupies rather than subtracting the entire driver from both.
Braces, terminals, access panels, and internal structures also need a physical assignment. A brace entirely inside the rear chamber does not reduce the front air volume.
The internal front port assembly belongs in the front chamber’s ledger under the chosen cavity-versus-duct convention. An external segment affects acoustic length without occupying that internal cavity in the same way.
JL Audio’s enclosure-volume guidance through Garmin support explains gross-to-net displacement accounting. Apply that principle separately to the two defined chambers.
Use physical displacement, not cone swept volume. Sd times Xmax describes excursion-related geometry and cannot replace the occupied space of a motor, basket, brace, or duct.
Work Through a Two-Chamber Budget
Assume a hypothetical acoustic design independently specifies 18 L net rear volume and 14 L net front volume. These are illustrative targets, not a recommendation for every driver of a particular size.
Suppose rear displacement consists of 2.0 L of installed driver structure and 0.2 L of bracing. Rear gross cavity requirement is:
18 + 2.0 + 0.2 = 20.2 L
Suppose front displacement contains 0.2 L of driver structure, 2.4 L of internal port assembly, and 0.5 L of bracing. Front gross cavity requirement is:
14 + 0.2 + 2.4 + 0.5 = 17.1 L
The calculator inputs are 18, 14, 2.2, and 3.1 L. Its rear and front choices return 20.2 and 17.1 L, while the combined gross-cavity choice returns 37.3 L.
| Chamber | Net air target | Assigned displacement | Required gross cavity |
|---|---|---|---|
| Sealed rear | 18.0 L | 2.2 L | 20.2 L |
| Vented front | 14.0 L | 3.1 L | 17.1 L |
| Sum for planning | 32.0 L | 5.3 L | 37.3 L |
The summed row is a budget summary. It cannot be used as one shared acoustic cavity without changing the topology.
Convert Each Gross Volume Into Dimensions
For a rectangular chamber in centimeters, volume in liters is internal width times height times depth divided by 1,000.
Suppose both hypothetical chambers share 38 cm clear width and 32 cm clear height, with the split along depth. Their cross-sectional area is 1,216 cm².
Rear depth is 20.2 × 1000/1216 ≈ 16.6118 cm. Front depth is 17.1 × 1000/1216 = 14.0625 cm.
These are separate clear cavity depths. Adding a hypothetical 1.8 cm divider gives 32.4743 cm between the inside faces of the outer front and rear walls.
With simple 1.8 cm outer walls at both ends, external depth would be approximately 36.0743 cm. Actual panel overlap, driver mounting, access construction, and baffle thickness must be represented in the section drawing.
The geometric solution does not prove the driver or port fits. Check mounting depth, basket position, screw access, port route, brace clearance, and installation order before finalizing dimensions.
Keep Partition Material Outside Clear Cavity Volumes
The dividing panel is material between the chambers. If both cavity dimensions are already measured to its faces, that material is outside both gross cavity envelopes and should not be deducted again from each.
When deriving exterior dimensions from chamber depths, add the divider thickness once in the correct position. Counting it twice enlarges the enclosure; omitting it shrinks the intended cavities.
The driver’s cutout and installed boundary can complicate the local geometry. Preserve how the manufacturer’s physical displacement convention applies across the partition.
An access panel or removable chamber wall can also change the cavity boundary. Include its actual installed position rather than using a convenient outside measurement that ignores its thickness.
Keep the section drawing and volume ledger together so later construction changes update the correct chamber.
Solve Front-Port Geometry With Its Own Net Volume
Use the front chamber’s net target, not the 37.3 L gross-cavity sum, in the intended port and acoustic model.
The port needs its actual area, physical path, termination correction, flow assessment, and clearance. Its displacement may change as length or shape changes, requiring the front gross-volume ledger to be updated.
Do not assume equal-area shapes share every end correction or high-level flow property. A narrow folded slot and a round tube can require different treatment despite the same area.
If revising front volume or tuning, rerun the complete bandpass model rather than treating the front port as an independent resonator with no driver or rear-chamber interaction.
The sealed rear chamber also needs its intended sealing and loss conditions. Unintended leaks can make the built system depart from the defined topology.
Verify Both Chambers and the Complete Response
Before construction, audit separate targets, assigned displacement, gross dimensions, partition thickness, port route, and service access. Confirm that no driver or brace allowance was counted in both chambers accidentally.
After construction, use appropriate low-level and operating measurements to compare the complete system with the design. Check response, tuning-related behavior, excursion, distortion, compression, and unintended leaks under the relevant conditions.
Retain the driver data, alignment model, chamber targets, two ledgers, section drawing, front-port design, filtering, and verification results. The useful calculation is a pair of traceable chamber budgets tied to a complete bandpass design, not a single diameter-based volume recommendation.