How to Wire Four Speakers in Series Parallel

Wire four identical speakers as two series pairs, then connect those complete pairs in parallel across one appropriate amplifier output. Each pair has twice one speaker’s nominal impedance, and the two equal pairs in parallel return the combined nominal load to the impedance of one speaker.

Open the Series Parallel Speaker Wiring Calculator.

How to Wire Four Speakers in Series Parallel

Identify four identical passive loads and label them A, B, C, and D. Confirm their nominal impedance, terminal polarity, intended application, and the amplifier’s supported output mode before planning the connections.

The calculator accepts impedance per speaker, speakers per series group, and parallel-group count. For this arrangement, enter two speakers per series group and two parallel groups.

Its equation is Ztotal = Zspeaker × series count / parallel groups. Total speaker quantity is the product of the two counts, so two times two represents four speakers.

The output is nominal impedance, not DC resistance or a complete amplifier-compatibility verdict. Actual impedance variation, power distribution, and manufacturer connection guidance remain relevant.

Draw the Two Branches Before Connecting Anything

The intended network has two paths from amplifier positive to amplifier negative. One passes through A then B, and the other through C then D.

In terminal terms, the first branch runs from amplifier positive to A positive, from A negative to B positive, and from B negative back to amplifier negative. The second branch follows the same pattern through C and D.

Both branch starts connect to the same positive output node, and both branch ends connect to the same negative output node. The midpoint between A and B is not connected to the midpoint between C and D in this defined arrangement.

Make the diagram explicit and work with the equipment powered down and disconnected according to its instructions. Label leads before removing any existing connections.

KICKER’s series and parallel wiring paper illustrates the electrical connection rules. Use the actual terminal paths rather than assuming a physical left-to-right cabinet arrangement describes the circuit.

Calculate Each Series Pair First

Assume four hypothetical identical nominal 4-ohm speakers. The A–B series branch is 4 + 4 = 8 ohms. The C–D branch is also 8 ohms.

The two branches are connected in parallel, so:

1/Ztotal = 1/8 + 1/8 = 1/4

Ztotal = 4 ohms nominal

The calculator gives the same result with 4 × 2 / 2 = 4.

Nominal impedance per identical speaker Each two-speaker series branch Two branches in parallel
2 ohms 4 ohms 2 ohms
4 ohms 8 ohms 4 ohms
8 ohms 16 ohms 8 ohms
16 ohms 32 ohms 16 ohms

The cancellation of the two factors applies to this equal two-by-two arrangement. It is not a general rule that four arbitrarily connected speakers always equal one speaker’s load.

All four in parallel would give Z/4. All four in series would give 4Z. Those are different circuits with different voltage and current requirements.

Check Ideal Voltage and Power Sharing

Use the 4-ohm example with a hypothetical ideal 16 V RMS amplifier output and purely resistive speaker models. Each 8-ohm branch draws 16/8 = 2 A RMS.

Within a branch, two equal speakers divide the voltage equally, so each receives 8 V RMS. Each load dissipates 8²/4 = 16 W.

Four loads therefore receive 64 W total. The combined-load check gives 16²/4 = 64 W, confirming the same result.

Total output current is 4 A RMS because the two equal 2 A branch currents add in this resistive model. The series link within either branch carries that branch’s 2 A, not the complete 4 A output current.

These values are independent circuit examples, not measured powers in a real four-speaker system. Real impedance and frequency-dependent voltage division can alter individual behavior.

Do not infer that an amplifier supplies four times its original output merely because four speakers are attached. Its voltage, current, load, supply, and operating mode constrain what is available.

Keep Polarity Consistent Across Both Branches

The series link connects the first speaker’s negative terminal to the second speaker’s positive terminal. That connection allows the same branch current to pass through both with the intended relative polarity.

Connecting a branch to the amplifier with reversed polarity does not change its nominal impedance under the simplified model, but it changes its acoustic contribution relative to the other branch.

A load calculation therefore cannot detect every polarity error. A circuit can show the expected nominal or DC value while producing poor acoustic summation.

Use manufacturer terminal markings and the intended acoustic wiring diagram. Some multi-driver or crossover designs intentionally use a different polarity relationship, so do not override a documented complete design with a generic terminal rule.

For separate identical full-range cabinets, also check that their manufacturer permits the intended series use. A complete passive cabinet has a crossover and changing impedance, so series interaction is more complex than four ideal resistors.

Confirm What the Amplifier and Connectors Support

Compare the resulting load with the amplifier’s actual mode and documented minimum load. A 4-ohm nominal result does not establish that every amplifier can drive the arrangement.

Crown’s speaker-load reference provides nominal network examples. Use the actual amplifier manual for supported modes, ratings, and connection instructions.

Do not join independent amplifier outputs together at the branch nodes. The parallel relationship here is between passive branches across one intended output, not between unrelated powered outputs.

Cabinet link sockets may already be parallel, but verify their wiring. Using such a socket as though it created a series connection can produce an entirely different load.

Line-level links on powered speakers are another connection type and do not follow this passive output-load diagram.

Inspect the Disconnected Network Before Operation

Trace each lead against the labeled drawing. Check branch starts, series links, branch returns, terminal tightness, and accidental contact between conductors.

If each hypothetical nominal 4-ohm driver has a documented 3.2-ohm DC resistance, each series branch would measure approximately 6.4 ohms and both branches together approximately 3.2 ohms before lead and contact effects.

That DC result can be consistent with the nominal 4-ohm load. It should not be forced to equal the nominal label.

A DC check can help reveal gross open or short connections, but it cannot prove correct acoustic polarity, complete frequency response, or every driver’s health. Preserve the expected measurement boundary and actual schematic.

For dual-voice-coil drivers, this four-speaker arrangement assumes each “speaker” already has a defined internal coil connection. Reduce that coil stage first rather than treating the raw coils as though they were four complete identical drivers.

Understand How a Fault Can Change the Load

An open connection in one series branch can remove that complete branch, leaving the other 8-ohm branch in the 4-ohm example. The overall load changes even if two speakers remain connected correctly.

A short across one speaker can make the two branches unequal. In the simplified example, branches of 4 and 8 ohms combine to approximately 2.6667 ohms, with different power distribution.

These are diagnostic illustrations, not acceptable operating arrangements. Stop and resolve an unexpected network result according to the equipment procedure rather than using the remaining sound as proof that the wiring is suitable.

The examples also explain why identical branch construction matters. Unequal counts or mixed impedance values require a separate calculation for each branch and its individual voltage distribution.

Keep the Final Network Reviewable

Retain speaker models, nominal and DC references, the labeled two-branch diagram, calculator counts, total nominal load, amplifier mode, and any disconnected measurements.

After confirming the intended circuit, verify appropriate operation and acoustic contribution under the relevant equipment procedure. A matching impedance number alone does not establish correct polarity or complete system behavior.

If one speaker is replaced or removed, repeat the branch calculations and checks. The useful shortcut—two equal series pairs in parallel returning to one speaker’s nominal impedance—depends on preserving those exact equal-load assumptions.

Table of contents