Choose a two-way crossover frequency inside a region where both drivers can meet the required acoustic response, directivity, and output limits with the intended filtering. Calculate components only after establishing that usable overlap and an acoustic target; nominal impedance and driver diameter alone cannot choose the frequency.
Open the Speaker Crossover Calculator.
How to Choose a Crossover Frequency for a Two Way Speaker
Begin with the mounted woofer and tweeter responses, not a preferred capacitor value. Determine where the tweeter can operate appropriately, where the woofer remains useful, and how their radiation patterns compare through the proposed transition.
The embedded calculator returns an ideal first-order series capacitor from a selected electrical corner and a resistive load. It does not choose the frequency, provide a complete two-way network, or establish safe tweeter operation.
Use that result only as a limited component example after defining its assumptions. A real design may need a different electrical order, unequal branch corners, attenuation, compensation, or active processing to obtain the desired acoustic response.
Keep three quantities separate: intended acoustic transition, electrical filter setting or component corner, and the measured equal-magnitude crossing. They can differ because each driver contributes its own response and phase behavior.
Assemble the Driver Data Before Selecting a Target
Review the manufacturer’s response, impedance, recommended operating range, and filtering guidance. Then measure the drivers on the intended baffle under controlled and compatible conditions.
The baffle can alter response and diffraction behavior, so a manufacturer’s test fixture does not necessarily reproduce the installed result. Driver spacing, acoustic offsets, and cabinet geometry also affect the crossover region.
For the tweeter, identify its resonance behavior and the output conditions behind any recommended minimum crossover. A minimum frequency stated for one filter slope and level cannot automatically be used with a shallower network or a higher operating demand.
For the woofer, examine the useful upper range, breakup behavior, distortion, and narrowing directivity. A smooth main-axis trace does not establish a satisfactory off-axis match to the tweeter.
If the available data do not establish the required operating limits, preserve that uncertainty. Choosing a familiar frequency does not replace missing information about the actual drivers.
Find a Usable Overlap Region
An overlap region exists where both drivers can contribute to the intended acoustic target while meeting the relevant limits. It is not merely the region where both raw traces contain some output.
For a hypothetical design exercise, suppose the selected tweeter’s documented and measured behavior supports the intended filtering from 1.8 kHz upward at the required level. Suppose the mounted woofer’s response and directivity remain suitable through 3.0 kHz under the same design objective.
That suggests investigating candidates within the 1.8–3.0 kHz overlap. It does not mean every candidate or filter slope in that interval is acceptable. The stated limits are illustrative scenario information, not generic rules for tweeters or woofers.
Evaluate a candidate such as 2.4 kHz against the actual branch responses and combined radiation. If one branch needs excessive equalization or the off-axis transition is poor, another candidate or driver combination may be necessary.
Linkwitz’s crossover discussion frames the transition in terms of combined acoustic behavior and polar response. That perspective explains why overlap is a design requirement rather than a single-number lookup.
Choose an Acoustic Alignment and Output Objective
Define the desired branch slopes, magnitude relationship, phase behavior, and summed response. Also state the intended listening axis and relevant off-axis region.
The electrical network must work with each driver’s natural response to produce those acoustic branches. A second-order electrical filter does not necessarily produce a second-order acoustic response when combined with a driver that is already rolling off.
Linkwitz’s filter discussion explicitly notes that mounted-driver response and offsets affect the result of an electrical filter. Its active-circuit examples should not be copied as passive component recipes, but the electrical-versus-acoustic distinction applies directly.
Determine the required output level and operating band as well. A response that looks suitable at low level may not remain suitable when excursion, heating, or nonlinear distortion becomes limiting.
Avoid assigning safety to a filter-order label alone. The driver’s actual terminal signal, acoustic response, and operating limits determine whether the chosen arrangement is appropriate.
Calculate a Limited First-Order Example
To illustrate component math only, assume a 2.4 kHz first-order electrical corner, a 6-ohm resistive tweeter model, and an 8-ohm resistive woofer model.
For a series capacitor feeding the tweeter resistance:
C = 1 / (2 pi f R)
C = 1 / (2 pi × 2400 × 6) ≈ 11.0524 microfarads
This is the result available from the embedded capacitor calculator. It does not establish that a first-order high-pass is appropriate for the hypothetical tweeter.
For a separate ideal series-inductor woofer branch, L = R / (2 pi f), giving 8 / (2 pi × 2400) ≈ 0.530516 mH. This is an independent equation, not a second output supplied by the embedded tool.
| Candidate ideal electrical corner | Series capacitor for 6 ohms | Series inductor for 8 ohms |
|---|---|---|
| 2,000 Hz | 13.2629 µF | 0.636620 mH |
| 2,400 Hz | 11.0524 µF | 0.530516 mH |
| 3,000 Hz | 8.8419 µF | 0.424413 mH |
These are individually defined first-order component values. They are not a finished recommended crossover or a table of safe transition frequencies for unspecified drivers.
Evaluate Spacing and Directivity
As frequency rises, wavelength becomes shorter relative to driver separation. The path difference between the drivers changes with listening angle and can produce interference through the transition.
At an assumed sound speed of 343 m/s, wavelength at 2.4 kHz is approximately 343 / 2400 = 0.142917 m. A hypothetical 0.15 m center-to-center separation is therefore a little more than one wavelength.
For two ideal equal, in-phase point contributions separated vertically by 0.15 m, the first path-difference cancellation at that frequency would satisfy sin(theta) = wavelength / (2 × spacing), giving about 28.45 degrees. This simplified illustration is not a prediction for a complete crossover with real driver phase and directivity.
It shows why a main-axis magnitude plot is insufficient. Measure relevant vertical and horizontal angles and compare the transition’s radiation behavior with the intended listening area.
Reducing spacing, changing the transition, using different directivities, or choosing another driver arrangement may be more effective than adjusting a capacitor while ignoring the geometry.
Refine the Electrical Network With Actual Impedance
Real driver impedance varies with frequency. A nominal 6-ohm label does not mean the tweeter behaves as a 6-ohm resistor throughout the transition.
Use the measured impedance in a suitable circuit model, including component DCR, capacitor losses where relevant, attenuation networks, and source impedance. A generic percentage adjustment cannot represent all of these interactions.
Level matching can also change the network seen by the filter. Decide whether an attenuation network is intended to preserve an approximately constant resistive load or whether its interaction will be modeled directly.
Practical substitutions should be evaluated in the complete circuit. Selecting the nearest nominal capacitor or inductor value can change the electrical corner, but the important design question is how it changes the acoustic branches and sum.
Verify the Candidate Before Finalizing It
Measure each filtered driver separately and the combined loudspeaker at a consistent position and timing reference. Inspect the intended transition, relative phase, polarity behavior, off-axis response, distortion, and electrical load.
Check the output conditions that motivated the design. Low-level smoothness does not independently establish high-level operation or driver protection.
Keep the source driver data, mounted measurements, usable overlap rationale, selected acoustic target, component example, actual network, spacing, and verification results. The chosen frequency should emerge from that connected evidence rather than from a universal multiplier of resonance or an automatically generated parts value.