How to Calculate Added Mass for a Passive Radiator

Estimate passive-radiator added mass by calculating the effective moving mass required for a stated resonance model, then subtracting its current effective moving mass. Include both suspension stiffness and box-air stiffness, and verify the finished system because a single-radiator spring-mass estimate does not model every coupled loudspeaker behavior.

Open the Passive Radiator Tuning Calculator.

How to Calculate Added Mass for a Passive Radiator

A passive radiator replaces the moving air in a conventional port with a diaphragm and suspension. Its mass and compliance interact with the enclosed air, so changing mass can change resonance without changing the physical enclosure volume.

Adding mass generally lowers resonance when stiffness remains unchanged. It does not automatically improve output, extension, excursion margin, or the complete alignment. The active driver and radiator must still operate together within their mechanical and acoustic limits.

The calculator uses a simplified single-radiator lumped model. It combines radiator suspension stiffness with the restoring stiffness of the box air and solves the ideal mass needed at a target resonance.

It does not include the full coupled active-driver response, damping and leakage, nonlinear suspension behavior, frequency-dependent radiation loading, or multiple radiators. Treat the result as a transparent starting estimate rather than verified final system tuning or a guaranteed amount of hardware to attach.

Gather Parameters with Compatible Definitions

Obtain net cavity volume, effective radiator area Sd, mechanical compliance Cms, and current effective moving mass from appropriate manufacturer data or measurement. Use the radiator’s values, not the active woofer’s parameters.

Effective area is not simply the area calculated from the advertised frame diameter. Sd describes the effective moving diaphragm area under the parameter convention. A nominal 10-inch radiator does not provide a defensible Sd value solely from its name.

Check the moving-mass convention carefully. A value including air load is not the same as the physical mass of the cone assembly weighed on a scale. The calculator asks for current effective moving mass including air load, consistent with its stated lumped model.

Include any mass already attached under the same convention. If the published baseline includes a factory tuning weight, do not add that weight again. Record whether screws, washers, retaining hardware, and previous added weights are already part of the current configuration.

Dayton Audio’s DMA45-PR specification distinguishes moving mass including air load, compliance, and effective area. Its specific values belong to that radiator; the important planning step is preserving the definitions rather than substituting a similar-looking model’s parameters.

Convert Units Before Combining Stiffness Terms

The physical spring-mass equation uses SI units. Convert net volume from liters to cubic meters by dividing by 1,000, and effective area from square centimeters to square meters by dividing by 10,000.

Convert compliance from mm/N to m/N by dividing by 1,000. Mechanical suspension stiffness is the inverse of that compliance: Ks = 1/Cms in N/m.

For example, Cms equal to 1 mm/N becomes 0.001 m/N and therefore represents stiffness of 1,000 N/m. Treating 1 mm/N as 1 m/N would underestimate this stiffness by a factor of 1,000.

Use mass in kilograms inside the resonance equation and convert the answer to grams afterward. Keep the calculator’s field units visible when entering data, especially when a manufacturer sheet uses different units for area or compliance.

Calculate the Box-Air and Suspension Stiffness

For the model’s one radiator moving against the box-air spring, air stiffness at the diaphragm is Kair = ρc²Sd²/Vb. Here ρ is air density in kg/m³, c is sound speed in m/s, Sd is effective area in m², and Vb is net air volume in m³.

The effective total stiffness is Ktotal = Kair + Ks. Both restoring terms oppose diaphragm displacement, so they add in this simplified model.

The ideal required mass at target frequency f is Mrequired = Ktotal/(2πf)². This gives kilograms when the input units are consistent. Added mass is Mrequired − Mcurrent.

The model treats box pressure through this ideal air-stiffness term and does not solve the active driver’s coupled motion. It is therefore more limited than a full passive-radiator enclosure simulation. State that boundary near the calculation, particularly when using the result to plan a finished loudspeaker.

Do not omit the suspension stiffness merely because the box air also acts as a spring. Whether the omission is small depends on the actual parameters; it cannot be assumed for every radiator.

Worked Example: A 40 L Cavity and 30 Hz Target

Assume an illustrative single radiator with effective area 400 cm², compliance 1 mm/N, and current effective moving mass of 100 g. Use a 40 L net cavity, target resonance of 30 Hz, air density 1.2 kg/m³, and sound speed 343 m/s.

Convert the dimensions: Sd is 0.04 m², volume is 0.04 m³, compliance is 0.001 m/N, and current mass is 0.1 kg. Suspension stiffness is 1,000 N/m.

Air stiffness is 1.2 × 343² × 0.04²/0.04, or approximately 5,647.152 N/m. Total stiffness is therefore 6,647.152 N/m.

Required mass is 6647.152/(2π × 30)², approximately 0.187083 kg or 187.083 g. Subtracting the current 100 g gives approximately 87.083 g additional effective mass under the model’s assumptions.

Enter those values in the calculator. Select total required effective mass to check approximately 187.083 g, then select additional mass to check approximately 87.083 g. The two outputs answer different questions and should not be interchanged when preparing a physical adjustment.

Check the Resonance and Mass Sensitivity

With the same total stiffness and the original 100 g mass, predicted resonance is sqrt(Ktotal/M)/(2π), approximately 41.03 Hz. Increasing the effective mass to the calculated 187.083 g lowers the model resonance to 30 Hz.

Target model resonance Required total effective mass Addition above the assumed 100 g
25 Hz 269.399 g 169.399 g
30 Hz 187.083 g 87.083 g
35 Hz 137.448 g 37.448 g
40 Hz 105.234 g 5.234 g

Mass rises with the inverse square of target frequency when stiffness is fixed. Small frequency reductions can therefore require substantial additional mass, with consequences for the suspension and mounting system.

If suspension stiffness were incorrectly omitted in the 30 Hz example, the required mass would be only about 158.938 g. That is approximately 28.145 g below the model including compliance. This numerical difference shows why the parameter should not be discarded without justification.

Interpret a Negative Added-Mass Requirement

If the target requires less effective mass than the current assembly, adding weight cannot achieve it under the fixed-stiffness model. The additional-mass output is unavailable for that condition rather than representing a physically meaningful negative weight to add.

Review whether removable tuning mass exists and whether the manufacturer supports changing it. Do not remove structural parts or assume that reducing hardware mass preserves the diaphragm’s integrity or parameter convention.

Other design changes, such as cavity volume or a different radiator, alter stiffness and the required mass. Those changes also affect the complete enclosure behavior and need their own simulation and verification.

Do not convert a negative result into zero and declare the requested resonance achieved. Zero addition means retaining the current configuration, whose predicted resonance can differ from the target.

Distinguish Free-Air Resonance from Installed Behavior

SB Acoustics’ mass-trimming note shows that increasing moving mass changes free-air resonance and mechanical Q under its parameter model. Those free-air relationships describe the radiator itself, not the complete installed box response.

For example, doubling mass at unchanged suspension stiffness reduces free-air resonance by the square root of two. An illustrative 20 Hz free-air resonance would become about 14.14 Hz. The installed resonance also includes box-air stiffness and should not be set equal to that free-air value.

Keep free-air resonance, the simplified installed model resonance, and the completed system’s measured acoustic behavior distinct. The frequency of a response peak or a low-frequency extension point is another quantity again.

Multiple radiators need a model that includes their shared coupling and individual mass. Do not enter the sum of their areas into this single-radiator tool and assume the reported mass is automatically correct per radiator.

Apply and Verify an Approved Mass Adjustment

Use the manufacturer’s intended mass attachment and permitted adjustment range. Secure added mass according to its instructions and account for all relevant hardware. Mechanical balance, clearance, orientation, and suspension loading matter in addition to the gram total.

Review active-driver and radiator excursion over the intended operating range and level in a complete simulation. A predicted resonance alone does not establish sufficient radiator displacement or protect the active driver below tuning.

After assembly, verify the system using appropriate low-level impedance and acoustic measurements, then compare the observed behavior with the model. Record net volume, radiator parameters and conventions, actual added hardware mass, orientation, and measured result so later adjustments remain traceable.

Table of contents