Calculate a first-order crossover inductor in millihenries with L = 1000R/(2πf), where R is an explicit resistive driver model in ohms and f is the electrical corner in hertz. Check winding resistance, tolerance, current behavior, and the real driver’s response before selecting the installed component.
Open the Crossover Inductor Calculator.
How to Calculate a Crossover Inductor in Millihenries
The simple calculation applies to a series inductor feeding a resistive load, with output taken across the load. This arrangement forms a first-order electrical low-pass section, reducing the load voltage progressively at higher frequencies.
Its ideal corner occurs when inductor reactance equals load resistance. Since inductive reactance is XL = 2πfL, setting XL equal to R gives L = R/(2πf) in henries.
Multiply by 1,000 to obtain millihenries. The unit conversion is essential: 0.001 H is 1 mH, while 1 H is 1,000 mH. A plausible-looking numeric output without its unit can describe a completely different component.
The embedded calculator supplies this ideal first-order estimate. It does not design a higher-order crossover, account for a complete impedance curve, or establish the final acoustic crossover frequency between real drivers.
Define the Circuit Before Choosing a Formula
A series inductor and a resistor form the specific model used here. An inductor placed across a driver in a high-pass network has a different role, while an inductor in an impedance-correction or notch circuit follows a different design requirement.
Higher-order low-pass sections also need their complete topology and alignment. A second-order network normally includes both inductance and capacitance, and its coefficients cannot be inferred just by multiplying the first-order value by an unexplained correction factor.
If replacing an inductor in an existing loudspeaker, identify the schematic and original specifications. Matching inductance alone may not preserve its response if the replacement has significantly different winding resistance or core behavior.
Georgia State University’s crossover overview illustrates how series inductors and capacitors occupy different branches. Circuit position, load, and output reference belong beside the component value in the design record.
Choose a Frequency and a Driver Impedance Model
Select an electrical corner appropriate to the intended driver and acoustic design. Use manufacturer response, impedance, and operating guidance rather than selecting a frequency solely because it is a common calculator default.
The driver’s acoustic response may narrow, break up, or fall naturally before the electrical filter reaches its ideal slope. Those features affect the useful handover region. The inductor formula cannot determine whether the adjacent driver will integrate well there.
For the initial calculation, state the resistive load assumption explicitly. A nominal 8-ohm driver does not remain exactly 8 ohms at every audio frequency. Its DC resistance is also not a complete substitute for its audio-frequency impedance.
When moving to a final simulation, use measured complex impedance and the driver’s acoustic response on the actual baffle. A nominal result is useful for understanding scale and checking units, while measurement-based modeling addresses the real branch behavior.
Worked Example: An 8-Ohm Model at 1,800 Hz
Assume an illustrative first-order low-pass section with an 8-ohm resistive load and a desired 1,800 Hz electrical corner. Calculate L = 8/(2π × 1800) henries.
The result is approximately 0.000707355 H. Multiplying by 1,000 gives 0.707355 mH, which is the expected calculator output for those inputs.
Check it independently by calculating reactance at 1,800 Hz: 2π × 1800 × 0.000707355, approximately 8 ohms. Matching reactance and resistance confirms the ideal corner and the henry-to-millihenry conversion.
For this isolated ideal section, the output magnitude at the corner is 8/sqrt(8² + 8²), approximately 0.7071 of the input voltage, or −3.01 dB. The response approaches a 6 dB-per-octave decline well above the corner; it is not a sharp cutoff.
If the load changes to a 4-ohm resistive model with the same intended frequency, calculated inductance halves to approximately 0.353678 mH. Keeping the original inductor would change the electrical response, so a component should not be transferred between different loads without recalculation.
Compare Frequency Choices and Available Values
For the same 8-ohm model, lower corners require larger series inductors:
| Intended electrical corner | Ideal calculated inductance |
|---|---|
| 500 Hz | 2.546479 mH |
| 1,000 Hz | 1.273240 mH |
| 1,800 Hz | 0.707355 mH |
| 2,500 Hz | 0.509296 mH |
| 4,000 Hz | 0.318310 mH |
An available 0.68 mH part gives an isolated ideal 8-ohm corner of 8/(2π × 0.00068), approximately 1,872 Hz. A 0.75 mH part gives approximately 1,698 Hz.
These are alternative electrical results, not interchangeable exact matches to the 1,800 Hz target. Choose practical values through the full circuit and acoustic design rather than assuming the numerically nearest part is always correct.
Tolerance introduces another difference between the nominal part and its actual value. Record the specified tolerance and, where relevant, the measured component value. Do not report an installed crossover corner to excessive precision while using a broadly toleranced nominal inductor and an approximate driver load.
Include Winding Resistance in the Response
An actual inductor has winding resistance in series with its inductance. Let that resistance be r and the ideal driver resistance be R. The load-voltage magnitude becomes R/sqrt[(R + r)² + (2πfL)²].
Unlike the lossless model, the low-frequency voltage ratio is now R/(R + r), below one. The frequency where the response is 3.01 dB below that reduced passband is (R + r)/(2πL).
For an illustrative 0.68 mH coil with 0.6 ohm winding resistance feeding an 8-ohm resistor, low-frequency ratio is 8/8.6, approximately 0.9302, or −0.628 dB relative to input. Its minus-3-dB point relative to that reduced passband is approximately 2,013 Hz.
This example deliberately uses stated hypothetical coil properties. It shows why a replacement with the same 0.68 mH inductance but a different winding resistance can alter both level and response. Do not treat the ideal 1,872 Hz value as a complete prediction for that lossy circuit.
Check Current, Heating, and Core Behavior
Winding heat follows I²r for the relevant RMS current. An illustrative 2 A RMS through 0.6 ohm winding resistance produces 2.4 W of winding dissipation. Current varies with signal and frequency, so choose the operating condition deliberately.
An air-core coil does not have magnetic-core saturation, but its winding resistance, thermal behavior, size, and mounting still matter. A magnetic-core design can offer different size and resistance tradeoffs, while its inductance and distortion behavior under current need suitable data.
Use the manufacturer’s specifications rather than inferring capability from wire gauge alone. Jantzen Audio’s coil catalog lists inductance, DC resistance, wire size, and physical dimensions as separate properties. That is the kind of component information needed for a meaningful comparison.
Avoid treating a low-resistance replacement as an automatic upgrade in an existing design. The original winding resistance may be part of the modeled response. Changing it should trigger circuit and acoustic checks rather than a claim of improvement based only on the lower ohm figure.
Measure and Mount the Component Deliberately
An appropriate LCR or impedance measurement can check inductance and winding resistance under stated test conditions. A multimeter’s ordinary resistance range measures winding resistance, not inductance. Keep the two readings separate.
Inductance measurement depends on the instrument method and test frequency, particularly for components with cores or significant losses. Use the manufacturer’s measurement conditions when comparing a measured value with its published specification.
Mount coils securely, account for their physical weight, and follow the intended layout to manage unwanted coupling between nearby inductors. A crossover is a physical assembly as well as a schematic, so changing coil placement can introduce effects not represented in an isolated-component calculation.
Keep lead routing, connection quality, and nearby heat sources consistent with the design. Mechanical convenience should not silently change circuit connections or place a heat-sensitive part beside a component expected to dissipate substantial power.
Verify the Complete Low-Pass Branch
Measure the driver through the installed crossover and compare its response with the intended acoustic target. Then inspect the combined response with the adjacent driver using a consistent timing reference and microphone position.
Review system impedance and off-axis behavior as well as the main-axis sum. A correct nominal inductor calculation does not guarantee suitable acoustic phase, directivity, driver protection, or amplifier load.
Retain the selected electrical corner, load assumption, ideal inductance, installed part value, winding resistance, component data, schematic, and measured result. A future replacement can then be assessed against the actual design requirements instead of matching only the printed millihenry number.