Calculate a three way speaker crossover by defining the woofer-to-midrange and midrange-to-tweeter regions, choosing an electrical topology, and calculating each component separately. Simple first-order values provide ideal section estimates; a finished loudspeaker needs measured driver impedance and acoustic response to establish its actual crossover.
Open the 3 Way Crossover Calculator.
How to Calculate a Three Way Speaker Crossover
A three-way system assigns low frequencies to a woofer, a middle band to a midrange driver, and high frequencies to a tweeter. It normally has two handover regions rather than one universal crossover frequency.
For a simple first-order electrical model, the woofer branch uses a series inductor, and the tweeter branch uses a series capacitor. The midrange needs both high-pass and low-pass behavior, commonly represented initially by a capacitor and an inductor in its branch.
The embedded calculator reports one of four individual section values at a time. It assumes nominal resistive driver models and ideal components. It does not calculate an optimized three-way acoustic alignment, compensate driver response, or establish that a selected crossover frequency protects a particular tweeter.
Keep the distinction between a component estimate and a system design visible throughout the process. Four plausible component values can still produce unsuitable combined response when connected to real drivers in a real baffle.
Choose Handover Regions from Driver Data
Start with each driver’s measured or manufacturer-published usable range. Look for frequency response, impedance, resonance behavior, distortion information, and recommended crossover conditions. A frequency where a driver still makes sound is not necessarily a suitable place to cross it.
The woofer should behave acceptably through its transition to the midrange. The midrange needs enough usable bandwidth on both sides of its assigned band. The tweeter’s lower transition must respect its operating requirements, including the slope or processing conditions specified by its manufacturer.
Consider directivity as well as on-axis amplitude. A large driver may narrow its radiation pattern before its response falls. Crossing it to a smaller driver with much wider radiation can change the room’s reflected sound even if the single on-axis curve appears smooth.
Driver spacing and baffle geometry also influence the combined pattern. The crossover cannot make three physically separated sources behave identically at every listening angle. Select candidate handovers that suit the actual drivers and enclosure, then model and measure the transition regions.
Calculate First-Order Components with Explicit Units
For a series inductor feeding a resistive load, the isolated first-order low-pass corner occurs where inductive reactance equals the load resistance:
L = R/(2πf)
This gives inductance in henries when R is in ohms and f is in hertz. Multiply by 1,000 to express the result in millihenries.
For a series capacitor feeding a resistive load, the isolated first-order high-pass corner occurs where capacitive reactance equals resistance:
C = 1/(2πfR)
This gives capacitance in farads. Multiply by 1,000,000 for microfarads. Confusing farads with microfarads or henries with millihenries produces errors of thousands or millions, so retain the units on every worksheet line.
The formulas describe individual ideal sections. A capacitor in series with a tweeter acts differently from a capacitor connected directly across an amplifier output. Component position is part of the topology; the numerical value alone does not tell you how to wire it. Georgia State University’s crossover overview illustrates the different branches and their filtering roles.
Enter Each Driver’s Own Impedance Model
Enter the lower electrical corner and the higher electrical corner, with the higher value above the lower one. Then enter separate nominal resistance models for the woofer, midrange, and tweeter.
Do not assume all three drivers share the completed cabinet’s nominal impedance. A cabinet labeled 8 ohms can contain drivers and networks with different individual impedance characteristics. The manufacturer’s cabinet label does not supply the load resistance for every component formula.
Use the component selector to calculate the woofer inductor, midrange high-pass capacitor, midrange low-pass inductor, and tweeter capacitor individually. Write down both the result and the selected component name. A value in microfarads must not be added to a value in millihenries to create a combined crossover size.
If the real driver impedance near the chosen corner differs markedly from the nominal model, use measured complex impedance in a suitable simulation. Substituting the driver’s DC resistance into every equation is not an equivalent correction because its audio-frequency impedance includes reactive behavior.
Worked Example: 500 Hz and 3,000 Hz Section Estimates
For an illustrative calculation, choose a lower electrical corner of 500 Hz and an upper corner of 3,000 Hz. Assume an 8-ohm resistive model for each of the three drivers. These are example inputs, not recommended crossover points for unspecified products.
The woofer’s isolated series-inductor estimate is 8/(2π × 500) henries, or approximately 2.546 mH. The midrange’s isolated high-pass capacitor estimate is 1/(2π × 500 × 8) farads, or approximately 39.789 microfarads.
At the upper corner, the midrange’s isolated low-pass estimate is 8/(2π × 3000) henries, or approximately 0.4244 mH. The tweeter’s series capacitor estimate is 1/(2π × 3000 × 8) farads, or approximately 6.631 microfarads.
| Selected component | Isolated section model | Calculated example value |
|---|---|---|
| Woofer series inductor | 8 ohms, 500 Hz low-pass | 2.546 mH |
| Midrange series capacitor | 8 ohms, 500 Hz high-pass | 39.789 microfarads |
| Midrange series inductor | 8 ohms, 3,000 Hz low-pass | 0.4244 mH |
| Tweeter series capacitor | 8 ohms, 3,000 Hz high-pass | 6.631 microfarads |
These values should agree with the calculator when each component is selected in turn. They are a list of initial section estimates, not a complete bill of materials or an assurance of flat response when all branches are combined.
Account for Interaction in the Midrange Branch
The midrange’s capacitor and inductor share a circuit. With both in series with an ideal resistive driver, their reactances oppose one another, and the branch behaves as a series RLC band-pass network. It is not the same as multiplying two independently buffered first-order filter responses.
For this simple series arrangement, the driver-voltage magnitude relative to the input is R/sqrt(R² + (2πfL − 1/(2πfC))²). Both component values appear in the expression, so changing either one affects the total midrange response.
Consequently, the isolated 500 Hz and 3,000 Hz calculations do not establish the complete branch’s exact two minus-3-dB frequencies. At 500 Hz, for example, the inductor is already contributing reactance; it cannot be ignored merely because it was chosen using the upper frequency.
Use a circuit simulator with the actual topology before describing final corner frequencies or the midrange passband. For a real loudspeaker, include measured impedance and the driver’s acoustic response too. Additional impedance correction, attenuation, or different filter orders may be necessary, but those should follow a defined model rather than arbitrary component multipliers.
Distinguish Electrical Order from Acoustic Slope
An isolated ideal first-order section approaches a 6 dB-per-octave stopband slope. The resulting acoustic response combines that electrical filtering with the driver’s natural response and enclosure effects. It does not automatically retain the same slope.
A tweeter with its own low-frequency roll-off may produce a steeper acoustic decline than the capacitor’s electrical response alone. A woofer’s breakup or a baffle transition can also change what the microphone measures. System summation depends on both amplitude and phase through each overlap region.
Siegfried Linkwitz’s crossover discussion treats the combined acoustic behavior and radiation pattern as design requirements. It is a useful reminder that textbook electrical curves are only part of a loudspeaker crossover design.
Do not prescribe a universal driver-polarity reversal from the phrase three way alone. Required polarity and phase behavior depend on the chosen acoustic alignment, actual responses, driver positions, and filtering. Check the intended design and measured sum rather than borrowing a wiring rule from a different crossover order.
Evaluate Real Components and the Measured Result
Choose practical component values only after considering tolerances and losses. For example, substituting 6.8 microfarads for the example’s 6.631-microfarad tweeter capacitor moves the isolated 8-ohm high-pass corner to approximately 2,926 Hz. A 0.47 mH inductor instead of 0.4244 mH moves the isolated 8-ohm low-pass corner to approximately 2,709 Hz.
Inductor winding resistance changes the branch impedance and level, while core behavior and current capability matter under load. Capacitors need appropriate voltage ratings, construction, and audio application suitability. Resistors used for level matching require dissipation checks. The four ideal values do not specify these physical requirements.
Measure individual filtered drivers and the combined system on the intended baffle, using consistent timing and microphone conditions. Review off-axis response and system impedance as well as the on-axis sum. Keep the schematic, measured data, component values, units, and polarity decisions together so each revision has a clear technical basis.